Safety and Compliance Information for Ring Yard Sign

Use Responsibly. Read all instructions and safety information before use.


Yard Sign intended for outdoor installation only. Only install the yard sign in the ground (grass, flower beds, etc.). Do not attempt to install in turf. Do not attempt to install in concrete, tar, or other paved surfaces. Do not attempt to install indoors.


Stake includes sharp edges that can cause injury. Improperly installed stake may present hazard to children. Exercise caution when driving stake into the ground. Do not place hands, fingers, or other limbs or extremities between the stake and the ground during installation. Ensure that stake is securely lodged in the ground. Do not install Solar Security Sign near play areas designated for children. Discontinue use if the sign or stake become damaged.

WARNING: Small parts contained in your device and its accessories may present a choking hazard to small children.

Use only a type LiFePo4 battery. Do not open, disassemble, bend, deform, puncture, or shred the battery. Do not modify, attempt to insert foreign objects into the battery or immerse or expose to water or other liquids. Do not expose the battery to fire, explosion, high temperature or other hazard. Fires involving lithium batteries can usually be controlled with flooding with water, except in confined spaces where a smothering agent should be used.

If dropped and you suspect damage, take steps to prevent any ingestion or direct contact of fluids and any other materials from the battery with skin or clothes. If a battery leaks, remove the battery and recycle or dispose of them in accordance with the battery manufacturer's recommendations. If fluid or other material from the battery comes into contact with skin or clothes, flush skin or clothes with water immediately. An open battery should never be exposed to water, as fire or explosion may result from exposure to water.

Insert the battery in the proper direction as indicated by positive (+) and negative (-) markings in battery compartment. Always replace with 14430 3.2V LiFePo4 battery specified for this product.
Always remove old, weak, or worn-out batteries promptly and recycle or dispose of them in accordance with applicable laws and regulations.

Product Specifications
Device Name: Ring Yard Sign
Model No.: 8ASYS5-0EN0
Input: Battery LiFePO4 14430 3.2V 400mAh
Operating temperature: -5 - 120F (-20.5 - 48.5C)

Recycling Your Device Properly
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of or recycle the device in accordance with your local laws and regulations. For information about recycling, go to For information regarding Amazon’s recycling program, visit


FCC Compliance Statement
This device and its related accessories like the adapter (the "Products") comply with part 15 of the FCC Rules. Operation of each Product is subject to the following two conditions: (1) each Product may not cause harmful interference, and (2) each Product must accept any interference received, including interference that may cause undesired operation.

Note: The Products have been tested and found to comply with the limits for a Class B digital device or external switching power supply, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The Products generate, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If a Product does cause harmful interference to radio or television reception, which can be determined by turning the Product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The party responsible for FCC compliance is Ring LLC, 12515 Cerise Ave, Hawthorne, CA 90250. /

Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at For information on our warranty and any other applicable policy, visit

If your device needs service, please contact Ring Customer Support. Contact details can be found at

Join Our Community

Share feature requests, get help, and discuss the latest in security with your fellow users on Ring's first neighbor-to-neighbor community forum.